The Chemise Sundress

Featured: Simplicity

The button-front “chemise” sundress— the quintessential of summer attire – is easy to wear, unrestrictive and yet not without that “sophisticated look”. This summer, you’ll find the sundresses  will be both elegant and appealing. And I am sure that because of its easy patterndraft, this lovely addition to your summer wardrobe will inspire you with your favourite fashion fabric.

You will need:

• 1 ½ yds. [1.5 m] of Fashion fabric, 60” [150 cm]wide
• 1 ¼ yds. [1.2 m] of Fusible interfacing 24” [60 cm] wide
• 12 buttons, 7/8” [22 mm] dia., line 34
• Coordinating thread
• Kraft paper

MEASUREMENTS

Bust – measure around fullest part of chest, just under the arms.

Hips –  measure around fullest part of seat, about 8” [20 cm] below waistline.

Back waist length – measure distance from nape of neck to waistline

PATTERN

A-B = back waist length

B-C = 2 times back waist length (or desired finished length**)

B-D = 4” [10cm]

Square across all points.

D-E = 1/2 of hip or bust measurement (whichever is the greater)

Square up and down from E to locate G, H.

I = half distance of A to B.

Square across to locate J.

I-K = 2” [5cm]; square across to locate L.

J-M = 3” [7.5 cm]

N = half distance of I to J.

Square down from N to locate O, P, and R.

N-Q = 1” [2.5 cm];  I-S = 1” [2.5 cm];  join M to Q.

T = half distance of B to P.

Square up and down from T to locate U and V.

L-W = 3” [7.5 cm]

H-X = 3” [7.5 cm]

Join W and X with a straight line.

Measure 1” [2.5 cm] on either side of P. Shape sideseam by joining Q and R with a smooth curve passing through the points on either side of P.

Measure ½” [12 mm] either side of T. Make a shaping dart by joining U and V with a smooth curve passing through the points on either side of T. (optional)

PINTUCKS

Trace out A-G-K-L.

Add ½” [12mm] at K and L. Join new points with a straight line.

Divide rectangle horizontally with 1 ½” [4 cm] intervals (3 in total) to create the pintucks.

Each pintuck is ½” [12 mm] wide with 1” [25 mm] spacing. (see diagram)

Trace out on fold S-Q-R-O-C for the dress back.

Trace out J-N-O-R-Q-M for the dress front.

Trace out L-W-X-N for the front placket.

Trace out on fold K-L-J-I for the dress facing.

Add ½” [12 mm] seam allowances to all pattern pieces.

Add 1 ¼” [ 32 mm] hem allowance to dress back and fronts.

**Design Note: This patterndraft can be shorten to waistline for a smart summer camisole.

CUTTING

Cut BACK 1X self on fold

Cut FRONTS 2X self

Cut FACING 1X self on fold;1X interfacing on fold

Cut PLACKET 2X self; 2Xinterfacing.

Cut PINTUCKS 1X self on fold

Cut 2 SHOULDER STRAPS =  16” long X 1” wide

[40 cm x 2.5 cm]

ASSEMBLY

1. Make 2 shoulder straps ¼” [6mm] wide.
2. Iron fusible interfacingto wrong side of dress facing and both placket pieces, following manufacturer’s directions.
3. Make the pintuckborder. Beginning at the top edge, turn under 1 ½” [4cm] and press. Stitch ½” [12 mm] parallel to folded edge. From stitching, turn under 1” [25mm] and press. Stitch ½” [12mm] parallel to pressed edge. From stitching, turn under 1” [25 mm] and press. Set aside.
4. Stitch the suppressiondarts on the back piece. (optional)
5. Stitch fronts to back along side seams. Press seam open.
6. Align and match bottom edge of pintuck border to top edge of dress. Pin/baste with right sides facing together. Machine stitch. Grade seam allowance and press upward.
7. From face side, baste along seamline (while tucking in the seam allowance) to complete last pintuck. From last pressed fold, stitch ½” [12 mm] parallel to seamline.
8. Press all pintucks downward on the face side of the dress.
9. Set shoulder straps in place on front and back. Baste to top edge of border.
10. Align and match dress facing to top edge of dress ensuring the straps are caught in the seam. Pin/baste in place. Machine stitch the seam. Grade seam allowance and press to one side. Understitch facing. Finish bottom of facing by turning under ¼” [6 mm] thentopstitching. Turn facing to inside of dress.
11. With right side of placket to wrong side of dress fronts, pin/baste placket to each front (allowing for seam allowance at top and hem). Stitch seam and press to one side.
12. On opposite side of placket, turn under seam allowance and press flat. Fold the short ends of the placket back on itself and stitch across top and bottom. Trim corners, then  turn plackets right side out. Align the pressed edge to the row of machine stitching andtopstitch closed.
13. On the right front placket, divide the length equally for 12 1-inch [2.5 cm] vertical buttonholes spaced 3 inches [7.5 cm] apart from the top. Position the first buttonhole 1″ [2.5cm] from the top of the dress front opening.
14. On the left front placket, sew on the buttons

       by wkdesigner.wordpress.com